Retro-reflective Photoelectric Sensor

5 out of 5 based on 2 reviews | Write a review

$50.22

Retro-reflective photoelectric sensor consists of light projector and light receiver in one, has long effective distance range with the help of reflective board. The supply voltage is DC 12V-24V (6-36V) or AC 110V-220V (90-250V). Infrared photoelectric sensor can distinguish the opaque reflective object, with less susceptible to interference, fast reaction, long life, high resolution and high reliability.

Dimension *
Model Selection for M12*1 *
Model Selection for M18*1 *
Model Selection for M30*1.5 *
Model Selection for 15.5*21*41mm *
Model Selection for 10.8*20*31mm *
Model Selection for 18*50*50mm *
Model Selection for 25*65*75mm *

SKU: ATO-PHOS-RR

Qty:

30-day Returns

Free Shipping

Delivery date: 6-12 days

Overview

Retro-reflective photoelectric sensor with reverse power protection, short circuit protection, current overload protection, can be directly connected with PLC.

Applications: Photoelectric sensors have been used as position detection, liquid level control, product counting, width discrimination, speed detection, fixed length cutting, holes recognition, signal delay, automatic door sensing, color scale detection, punching and cutting Machine and security and many other areas. In addition, using the stealthiness of infrared, photoelectric sensors also can be used as a burglar alarm in banks, warehouses, shops, and offices.

Specification:
1. DC/AC output:

Type		Round type			Square amplifier built-in type
Dimension		M12*1	M18*1	M30*1.5	15.52141mm	10.82031mm
DC type	NPN	NO	NO	NO	NO	NO
		NC	NC	NC	NC	-
		-	NO+NC	NO+NC	-	-
	PNP	NO	NO	NO	NO	NO
		NC	NC	NC	NC	-
		-	NO+NC	NO+NC	-	-
AC type	Two-wire	-	NO	NO	-	-
		-	NC	NC	-	-
Detection range		1m±10%	2m±10%	4m±10%	1m±10%	4m±10%
Detection target		Opaque object	Opaque object	Opaque object	Opaque object	Opaque object
Detection range regulation		Sensitivity controller	Sensitivity controller	Sensitivity controller	Fixed	Sensitivity controller
Response time		1ms	1ms	1ms	1ms	1ms
Connection delay		1.5ms
Light source		Infrared light 660nm
Power supply		DC type: DC 12-24V (6-36V), impulse (p-p) 10% below; AC type: AC 110-220V (90-250V) 50/60Hz
Withstand voltage		AC1000V 50/60Hz 1min between charging part and housing
Voltage influence		Inside ±15% rated supply voltage range, at rated supply voltage value, inside ±10% detection distance
Consumption current		N/P type: ≤20mA, A type: ≤1.7mA
Control output		N/P type: ≤300mA, A type: ≤400mA, J type: ≤2A (contact service life: 0.1 million times)
Loop protection		N/P/D type: reversal connection protection, surge absorption, load short-circuit protection, A type: surge absorption
Ambient temperature & humidity		Operation temperature/storage temperature: -30~65℃ (no freeze, no dew); Operation humidity/storage humidity: 35~95%RH
Temperature influence		Temperature range -30~65℃, at +23℃, ±15% detection distance; Temperature range -25~60℃, at +23℃, ±10% detection distance
Insulation impedance		≥50MΩ (DC500 megameter) between charging part and housing
Material		Housing: Nickel plated brass (ABS), Detection surface (lens): PMMA
Protection class		IP67
Cable length		1.2m

2. Relay output:

Type	Square relay built-in type
Dimension	185050mm	256575mm
Relay output	DC illuminated	DC illuminated
	AC illuminated	AC illuminated
	DC non-illuminated	DC non-illuminated
	AC non-illuminated	AC non-illuminated
Detection range	4m±10%	4m±10%
Detection target	Opaque object	Opaque object
Detection range regulation	Sensitivity controller	Sensitivity controller
Response time	30ms	30ms
Response frequency	DC: 0.5kHz, AC: 25kHz
Delay distance	≤10% detection distance
Connection delay	1.5ms
Light source	Infrared light 660nm
Supply voltage	DC type: DC 12-24V (6-36V), Impulse (p-p) 10% below; AC type: AC 110-220V (90-250V) 50/60Hz; DC/AC type: DC 12-240V/AC 24-240V, 50/60Hz
Withstand voltage	AC1000V 50/60Hz 1min between charging part and housing
Voltage influence	Inside ±15% rated supply voltage range, at rated supply voltage value, inside ±10% detection distance
Power current	≤3VA
Control output	≤2A (contact service life: 0.1 million times)
Allowed impulsion and vibration	B≤30g, T≤11ms, f≤55Hz, a≤1mm
Ambient temperature & humidity	Operation temperature/storage temperature: -30~65℃ (no freeze, no drew); Operation humidity/storage humidity: 35~95%RH
Temperature influence	Temperature range -30~65℃, at +23℃, ±15% detection distance; Temperature range -25~60℃, at +23℃, ±10% detection distance
Insulation impedance	≥50MΩ (DC500 megameter) between charging part and housing
Material	Housing: Aluminum die casting (ABS), Detection surface (lens): PMMA
Protection class	IP65
Cable length	1.2m

Wiring diagram:

Tips: How to install a retro-reflective photoelectric sensor?

When in choosing working point, installation and using a retro-reflective photoelectric sensor ensure that the infrared light receiver must work in the cut-off zone and the saturation zone.
The front end face of the photoelectric sensor and the surface of the detection workpiece or object must be kept parallel, so that the conversion efficiency of the photoelectric sensor can be highest.
The distance between the front end face of the retro-reflective photoelectric sensor and the reflective board remains within the specified range.
Retro-reflective photoelectric sensor must be installed in the place without direct strong light source.
The infrared projector current should be set at 2 ~ 10mA, because the luminous intensity and current linearity is the best. If the current is too large, the light attenuation of infrared projector will be big, and there is an affect of the life for a long working time. If in the case of battery supply, the current should be small, and the anti-interference ability will be decrease at this moment. Attention should be paid to avoid adverse factors such as external light interference.

Existing reviews of Retro-reflective Photoelectric Sensor

For your photoelectric sensor, how large the obaqe should be, so can it be detected?

For your photoelectric sensor, how large the obaqe should be, so can it be detected?

From: Dpolito | Date: 20/12/2021

Was this review helpful? Yes No (0/0)

ATO Responded

The photoelectric switch can detect objects larger than 5mm.

I am very satisfied with the retro-reflective photoelectric sensor

I am interested in purchasing a digital counter with a sensor for a manufacturing process of small coated water seal rings. Currently, we weigh our boxes to count the number of products in each order which is time consuming and less than accurate. The counter/sensor needs to be capable of sensing non-metal products as well as capable of being set at two different count settings (500 and 1000 items). I would also like to know if a counter would be capable of pausing production when the desired value is reached. Please let me know which products would allow for these specifications?

From: Gallion | Date: 23/04/2021

Was this review helpful? Yes No (0/0)

ATO Responded

Our "Dual output counter & Photoelectric sensor" will be ideal to meet these requirements, see specs and prices at the web site.

Load more reviews...

Write your review for Retro-reflective Photoelectric Sensor

Only registered users can write reviews

Review title:

Review text:

Rating:

Bad
Excellent

Customers who bought this item also bought

Digital Counter, 6 Digit, Up/Down, Number/Length/Batch

$89.14

SKU: ATO-DIGC-FH6D

6 digit counter can be used for counting number/length/batch, position control of balers controlled by variable frequency motor, and measuring height, position and angle. Digital counter with up/down input modes can preset count value or length, and simultaneously display the total count, counting length and batch value in real time.

Retro-reflective Photoelectric Sensor

Through Beam Photoelectric Sensor

Diffuse Reflective Photoelectric Sensor

Proximity Sensor, Inductive, M6, 2 Wire, 24V

Digital Counter, 6 Digit, Up/Down, Number/Length/Batch